Dev:SemanticConstraints

From railML 2 Wiki
Revision as of 14:58, 18 May 2020 by RailML Coord Documentation (talk | contribs) (Migration wiki2→wiki3)
Jump to navigation Jump to search
🗒️ This page is mirrored from page Dev:SemanticConstraints in The railML® 3 wiki.

Semantic constraints
 

XML Schema Definitions (XSDs) offer a variety of possibilities to define syntactic constraints, describing the syntax of an XML file, including the type and multiplicity of an element. For example in railML® 2, it is possible to describe and validate that a <train> must reference one or more <trainPart>s, that all <trackElements> must have a position on the <track>, that the length of a <tunnel> is a decimal number and that allowed positions of <couplers> are at the front, rear or both ends of a <wagon>. However, XML Schema Definitions are not able to express a constraint on one element or attribute that depends on the value or existence of another element or attribute. One example is that an XSD cannot express that a departure time must be greater than or equal to the arrival time, or that it does not make sense to specify a stopOnRequest and at the same time that the train is not allowed to stop. Such rules restricting the contents, or semantics, of one element or attribute depending on other content, are called semantic constraints.

Semantic constraints are as important as syntactic constraints. If they are ignored, other software may not be able to handle your railML® files, or may interpret the contents in different ways. Therefore, their implementation will be checked during certification.

Elements with approved semantic constraints are listed in Category:Semantic constraints. On the element documentation pages, the semantic constraints can be found in a dedicated chapter below the syntactic constraints. Proposed semantic constraints are listed in Category:Semantic constraints_proposed. A list of the semantic constraints by introduction date of a can be found below.

Every application of railML® has to be checked not only on XSD compliance but also on the obedience to the semantic constraints.

How to introduce Semantic Constraints

Constraints that can be described by XML Schema Definitions (XSDs) should be implemented syntactically in the schemas. Please, follow the guideline for participating in the development process. If a constraint cannot be described by XML Schema Definitions, you can propose a semantic constraints.

Semantic constraints can be proposed either by one of the railML® working groups (link to the railML® website) or suggested by anyone through a post in the forum (link to the railML® website).

If there is consensus in a working group to add a new semantic constraint, a post will be made in the forum and the proposed constraint will be added to the element documentation using Template:Semcon, with status=proposed and added to the list below. If there are no objections in the forum, it will be approved after six weeks and implemented in the wiki with status=approved.

If you see the need for a semantic constraint beyond the schema, please discuss it in the forum (link to the railML® website) and then add a proposal in the element documentation using Template:Semcon, with status=proposed. Please also add the proposal to the list below! If a consensus is reached in the forum, the proposal will be accepted, it will implemented in the wiki with status=approved.

🗒️ Semantic constraints that have been proposed before the 10th of December 2018 shall be considered as approved until decided otherwise.

Design guidelines

Current Constraints as of railML 2.5

View/edit list on the separate source page.

Element ID Proposal date Date of acception Date of deprecation Description
<TT:timetablePeriod> TT:001 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other validity periods.
<TT:specialService> TT:018 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <specialService> validity periods of the same enclosing <operatingPeriod>.
<TT:operatingPeriodRef> CO:002 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given.
<TT:operatingPeriod> CO:002 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given.
<TT:operatingDay> TT:019 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <operatingDay> validity periods of the same enclosing <operatingPeriod>.
<TT:circulation> CO:002 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given.
<TT:blockPart> CO:002 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given.
<RS:designator> (introduced with version 2.5) RS:001 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with the validity periods of other entries of the same register of the same enclosing <state>.
<RS:operator> RS:002 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <operator> validity periods of the same enclosing <vehicle>/<classification>.
<RS:owner> (introduced with version 2.5) RS:003 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <owner> validity periods of the same enclosing <vehicle>/<classification>.
<RS:state> RS:004 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <state> validity periods of the same enclosing <vehicle>/<states>.
<IS:state> IS:020 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <state> validity periods of the same enclosing <states> collection. See also Dev:Defining temporal availability of infrastructure elements and speed profiles.
<IS:state (with length)> IS:021 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with other <state (with length)> validity periods of the same enclosing <states (with length)> collection. See also Dev:Defining temporal availability of infrastructure elements and speed profiles.
<IS:designator> CO:001 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with the validity periods of other entries of the same register of the same enclosing element.
<CO:designator> (introduced with version 2.5) CO:001 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given. Must not overlap with the validity periods of other entries of the same register of the same enclosing element.
<CO:phase> (introduced with version 2.5) CO:002 2018-11-12 2019-03-21 Any starting time stamp (as it may result e.g. from a combination of startDate and startTime) shall be lower or equal any ending time stamp (e.g. endDate) if both are given.
<TT:ocpTT> TT:002 2018-10-25 2019-06-20 The attribute sequence is shall be increasing according to the train path.
<TT:ocpTT> 2018-10-25 discarded No ocpRef is allowed to occur more than one time in the same <trainPart>
<TT:blockPart> TT:003 2019-07-13 2019-07-18 By means of a <blockPart> it is possible to model both journeys with and without reference to a <trainPart> within a roster, as well as services without change of location (without reference to a <trainPart>). These 3 basic types are distinguished by the attribute mission. The following table presents the semantic constraints: see table here (link to the railML® website)
<TT:blockPart> TT:004 2019-07-20 2019-07-18 vehicleRef and formationRef shall not be used within the same blockPart, since a blockPart is either one for a certain vehicle or one for a whole formation.
<TT:rostering> TT:005 2019-05-22 2019-06-25 vehicleRef and formationRef are to be used exceptional since the circulation plan is either one for a certain vehicle or one for a whole formation.
<TT:stopDescription> TT:006 2018-09-03 2019-06-20 Constraints between the attributes <ocpTT>.ocpType, <stopDescription>.guaranteedPass, .commercial, .onOff, .stopOnRequest and .operationalStopOrdered
<TT:stopDescription> (Stop on request / More than one stop type per OCP) TT:007 2019-06-19 discarded 2020-04-23
<TT:trackInfo> TT:008 2018-08-21 2019-06-20 The representation of differentiated track usage must not result in differences in arrival and departure times. In these cases, a separate <trainPart> / <train> with different arrival and departure times must be created.
<TT:trackInfo> TT:009 2018-08-21 2019-06-20 The operating days of the <operatingPeriodRef>s of the individual <trackInfo> entries must be disjoint and must not contain more traffic days than the parent <trainPart>. If fewer traffic days are provided in the <trackInfo> entries than the parent <trainPart> contains, the information (e.g. attribute trackInfo) of the parent <ocpTT> must be evaluated for these operating days.
<TT:times> (Correct encoding of run time supplements) TT:010 2019-06-19 2020-10-15 @scope='earliest' and 'latest' are not intended to encode supplement times, as this is redundant to <ocpTT>.<sectionTT>.<runTimes>@operationalReserve, @additionalReserve, @minimalTime.
<TT:times> TT:011 2019-06-19 discarded
<TT:times> TT:012 2019-06-19 2022-06-02 When @scope='actual' is used, then the operating period and/or timetable period specified at the trainpart level shall refer to only one operating day. Like this the operating day to which the actual times refer is defined.
<TT:times> TT:013 2019-06-19 discarded
<TT:times> (Arrival times for passing OCP's) TT:014 2019-06-19 2022-06-02 @arrival is not to be specified if the attribute ocpType of the parent <ocpTT> has the value pass - use departure for run-through (passing) times; This is in line with the definition of @arrival as the moment at which the train ends its movement and gets to a halt at the parent <ocpTT>.
<TT:times> (Arrival time at first OCP) TT:015 2019-06-19 2022-06-02 At the first <ocpTT> of a <trainPart> that is not the first one of the <trainPartSequence>, the attribute @arrival is optional. If it is set anyway, then, for consistency reasons, the value of @arrival of the regarding <ocpTT> must be identical for both this <trainPart> and the preceding one.
<TT:times> (Departure time at last OCP) TT:016 2020-10-09 2022-06-02 At the last <ocpTT> of a <trainPart> that is not the last one of the <trainPartSequence>, the attribute @departure is optional. If it is set anyway, then, for consistency reasons, the value of @departure of the regarding <ocpTT> must be identical for both this <trainPart> and the subsequent one.
<TT:connection> TT:017 2022-12-15 2022-12-15 If the trainPartRef attribute is given, then there must also be a trainRef attribute, and the trainPartRef attribute must point to a train part of the train referenced by the trainRef attribute.
<IS:speedChange> IS:001 2019-04-11 discarded Always define trainRelation
<IS:trackEnd> IS:002 2019-06-17
<IS:trackBegin> IS:003 2019-06-17
<IS:ocp> IS:005 2019-06-19 2022-07-14 An <ocp> that refers to a parent <ocp> via an @parentOcpRef overwrites the attributes and elements of the parent <ocp> if explicitely defined. If an element is specified on an <ocp> that uses a @parentOcpRef any information provided with that element on a higher layer of the <ocp>-tree is overwritten. There is no merging of element-information from different levels. The same applies for attributes of <ocp>.
<IS:mileageChange> IS:006 2019-06-19
  • Define attributes @absPosIn and @absPos for "real" mileage changes
  • Define attribute @absPosIn alone in case of an ending mileage
  • Define attribute @absPos alone in case of a starting mileage
  • For starting mileages and "real" mileage changes, the @absDir has to be fiven to define the ongoing orientation of the mileage
<IS:propOperational> IS:007 2020-02-25 discarded
<IS:uptime> IS:008 2020-02-28 An <ocp> with <propOperational>@operationalType=blockSignal shall not have

@mode=manned (as a manned blockSignal shall be modelled in railML® 2.x as a blockPost).

<IS:uptime> IS:009 2020-02-28 An <ocp> with attribute <propOperational>@operationalType=stoppingPoint shall not have @mode=manned (as a stoppingPoint has no operational usage and therefore no operational staff by the IM).
<IS:uptime> IS:010 2020-02-28 An enumeration of several time periods by @from and @until for one <ocp> shall not overlap so that for every time there shall be a unique status of <uptime>.
<IS:speedChange> IS:011 2020-10-12 (date of creation of ticket 425) 2021-11-10 (40th conference slide 11) 2024-10-02 (railML.org Governance Coord approved)
  • Every <track> has to have at least one <speedChange> at the track begin with parameters @pos="0" and @dir="up".
  • Every <track> has to have at least one <speedChange> at the track end with parameters @pos="{value equal to trackEnd@pos}" and @dir="down".
<IS:speedProfile> IS:012 2022-03-14 @basicSpeedProfile is always linked with @influence=increasing
<IS:speedProfile> IS:013 2022-03-14
  • @influence=increasing: The <speedProfile> increases the permitted speed. If multiple "increasing" speed profiles are applicable, select the one with the highest @vMax value.
  • @influence=decreasing: The <speedProfile> decreases the permitted speed. If multiple "decreasing" speed profiles are applicable, select the one with the lowest @vMax value. If this value is lower than the speed of an "increasing" speed profile, it overrides that speed.
<IS:tunnel> IS:014 2022-03-14 Define the tunnel resistance factor @resistanceFactorPassenger resp. @resistanceFactorFreight only if @kind and @crossSection are not known.
<IS:ocp> IS:015 2022-07-14 2022-08-11 When specifying @parentOcpRef for an <ocp> circles are not allowed. That means that when following the chain of @parentOcpRef no <ocp> shall be visited twice.
<TT:times> TT:020 2024-11-21 No two attributes //<times>/@scope of the same enclosing stop/pass elements shall have the same value.